Page 6 - XBD-ISG样本

莲盛泵业 莲盛泵业

结构Structure
概述Overview

1、XBD型立式单级消防泵组，吸入和排出为水平方向的同一直线上，且口径相同。
XBD型立式单级消防泵组系本公司根据国内外市场的需求，借鉴国内外离心泵结构优点，借助CAD技术，最新研制
2、从电机端看为顺时针方向旋转
开发的新一代立式单级消防泵组。
3、轴封采用机械密封。
该泵结构新颖、占地面积小、重量轻、寿命长、输送清水及类似于清水的液体，适官消防供水及其它方面的给水.
1. XBD vertical single-stage fire pump set, the suction and discharge are on the same straight line in the
该系列产品符合GB6245-2006《消防泵》的要求
horizontal direction, and the caliber is the same.
额定流量范围:5~160L/s
2. Seen from the motor end,it is clockwise rotation .
额定压力范围:0.30~13MPa
3. the shaft seal adopts mechanical seal

XBD vertical single-stage fire pump set is a new generation of vertical single-stage fire pump set developed
安装和使用Installation and use
by our company based on the demand of domestic and foreign markets, drawing on the advantages of
centrifugal pump construction at domestic and abroad, and using CAD technology.
a、安装
The pump has novel structure, small volume, light weight, long service life, conveying clean waterand liquid
1、安装前必须进行检查，用手转动，转子回转必须自如。
similar to clean water, suitable for fire water supply and other aspects of water supply.This series of products
2、使用底脚螺栓与地面连接，可通过在泵底座与基础间塞足够厚底的垫铁对各基点调平。
meet the requirements of GB6245-2006 "Fire Pump".
3、支撑输出管路，避免泵装置承受附加载荷，泵出口采用柔软性接头与输出管路连接，以便安装和吸震
Rated flow range: 5~160L/s
4、每台泵有独立的进水管，采用自灌式吸水。
Rated pressure range: 0.30~1.3MPa
b、使用
1、不得在无水的情况下开动泵

型号Model 2、初次启动前应按下列程序操作:
完全关闭泵的出水阀门。
XBD / ISG 首先引水，打开进水口阀门充水，旋松泵上放气螺栓放气，有水喷出后拧紧放气螺栓。
G -
点动泵，从电机端看，泵为顺时钟旋转，如方向有误，在电动机接线盒中任意对调二相电源接头。
徐徐打开出口阀门，调节至额定工况。
企业自定义 Enterprise customization 3、在出口阀关闭的情况下，泵工作最长时间应小于3分钟。

G表示供水用途 G means water supply use
a, Installation
主要参数：额定压力MPa×10/额定流量L/S
1. It must be inspected before installation and rotated by hand. The rotor must be freely swung.
Main parameters; rated pressure Mpa x10 / rated flow L / s
2. Use the binding bolts to connect to the ground, Inserting a sufficiently thick block between the pump base
消防泵组（无D表示消防泵） Fire pump set (without D means fire pump) and the foundation in order to make each point in same level.
3. Support the output pipeline to avoid the additional load on the pump unit. The pump outlet is connected

with the output line by a flexible joint for installation and shock absorption.
示例:型号为XBD5.0/20G-ISG表示供水用途的，带电机驱动，额定压力为0.50 MPa，额定流量为20L/s的普 4. Each pump has a separate inlet pipe and adopts filling water from outside as water sucking

通消防泵组。
b, Use
Example: Model XBD5.0/20G-ISG stands for general purpose fire pump set with water supply. 1. Do not start the pump without water.
motor drive, rated pressure of 0.50MPa and rated flow of 20L/s. 2. The following procedures should be followed before the initial start:

Close the pump's outlet valve completely.

1 2